Gratis verzending vanaf 30 euro binnen Nederland!
Zelf afzetmoppen maken voor je medaka

DIY spawning mops for medaka: 4 materials tested

If you keep medaka, you know how exciting it is to discover eggs for the first time. But without the right tools, those eggs quickly disappear into the substrate or get eaten by the fish themselves. A spawning mop is the answer: a simple but effective device you can make yourself from ordinary yarn or foam. In this article I test four popular materials and explain step by step how to put together your own spawning mop. No expensive purchases needed, just get started yourself!


Which material works best for spawning mops?

Making a spawning mop is all about the structure of the material. Medaka attach their eggs to threads or fibres using tiny sticky filaments. The finer and softer the fibres, the better the eggs stay put. I tested four materials: 100% acrylic wool, polyester yarn, pool noodle strips and sisal rope. Each material has its own pros and cons, and the results were surprising.

Acrylic wool and polyester scored by far the best on egg adhesion. Sisal rope proved too rough and coarse, so the eggs barely stuck to it. Pool noodle strips are not suitable as a yarn substitute on their own, but they play another important role: they serve as the float for the mop. Below you can see an overview of the test results:

Comparison table: materials for spawning mops

MaterialEgg adhesionDurabilitySuitable as floatPrice
100% acrylic woolExcellentGoodNoLow
Polyester yarnGoodVery goodNoLow
Pool noodle stripsPoorExcellentYesLow
Sisal ropePoorModerateNoLow

Winner: 100% acrylic wool. This material has the finest fibres, is not toxic to fish, and is easy to find in any hobby shop or online. Polyester is a good second choice, especially if you want something that lasts longer and is easier to clean. Avoid materials that are bleached or contain synthetic dyes, because they can be harmful to both the eggs and the fish.


Floating or sinking mop: what suits you?

Not all medaka lay their eggs in the same place. In nature medaka (Oryzias latipes) look for aquatic plants at the surface, but in an aquarium or tub without plants they can also lay eggs on the bottom. That is why there is a distinction between floating mops and sinking mops, and both have a specific use.

A floating mop mimics the surface layer, where medaka naturally prefer to spawn. You attach the mop to a piece of pool noodle or cork so it stays afloat. This is ideal for outdoor tubs and aquaria where the fish swim actively at the surface. A sinking mop simply sinks to the bottom, sometimes with a small weight attached. This works well in deeper tubs or if you notice your medaka prefer the lower water layers.

When do you choose which type?

Floating mop:

  • Suitable for outdoor tubs and ponds
  • Ideal in summer when medaka spawn actively at the surface
  • Easier to check and remove daily
  • Imitates aquatic plants such as waterweed or hornwort

Sinking mop:

  • Suitable for deeper aquaria
  • Useful if your fish are shy and prefer to spawn in a sheltered spot
  • Works well combined with a substrate of gravel or sand
  • Less visible, which reduces stress for the fish

In practice many medaka breeders recommend using both types at the same time. That gives the fish a choice and increases the chance of successful egg laying. I always use two floating mops and one sinking mop per tub, and that works fine.


Step by step: making your own spawning mop

Now the fun part: get started yourself! You need very little and it takes you at most twenty minutes. Below you will find a complete materials list and assembly instructions for both a floating and a sinking mop.

Materials list

For one floating mop:

  • 1 piece of pool noodle (approx. 3 cm thick, 5 cm long)
  • 100% acrylic wool or polyester yarn (unbleached, dark colour works well)
  • A pair of scissors
  • A piece of fishing line or nylon thread (approx. 20 cm)
  • A plastic fork or piece of cardboard as a winding form

For one sinking mop:

  • 100% acrylic wool or polyester yarn
  • A small stainless steel nut or pebble as weight
  • Nylon thread
  • Scissors and winding form

Assembly instructions: floating mop

  1. Wind the yarn approximately 50 to 70 times around your winding form (a plastic fork works perfectly).
  2. Carefully slide the yarn off the form and tie it firmly in the middle with a piece of nylon thread.
  3. Cut the loops at both ends so you get loose threads.
  4. Push the nylon thread through the middle of your pool noodle piece.
  5. Knot the thread so the mop hangs firmly from the float.
  6. Shake the mop loose and fluff out the threads for a full, fluffy structure.
  7. Rinse the mop thoroughly with cold water before use.

Assembly instructions: sinking mop

  1. Follow steps 1 to 3 of the instructions above.
  2. Instead of a float, tie a small stainless steel nut to the nylon thread.
  3. Check that the weight is heavy enough to let the mop sink to the bottom.
  4. Rinse this mop thoroughly before use too.

Practical tip: Preferably use dark yarn (green, brown or black). Medaka feel safer with dark colours and are more likely to spawn near the mop.


Read on

Frequently asked questions (FAQ)

How often should I remove the eggs from the mop? Remove the eggs daily, especially in warm temperatures. Medaka eggs develop quickly (at 25 degrees Celsius in about 10 days) and if you leave them too long, the fish may eat them.

Can I use ordinary wool from the shop? Only if it is 100% acrylic or 100% polyester. Avoid wool of animal origin (such as sheep's wool), because it can promote fungi and sometimes contains lanolin, which can be harmful to fish.

How do I clean a spawning mop? Rinse the mop with warm water without soap after use. You can also briefly soak it in a lukewarm salt bath (aquarium salt) to remove bacteria. Then let it dry thoroughly before reuse.

How many mops do I need per tub? As a rule of thumb: use one mop per five to ten fish. During an active spawning period in summer you can happily hang two or three mops in the tub at the same time.

My fish ignore the mop. What am I doing wrong? Check that the mop is rinsed well and gives off no chemical odours. Sometimes it takes a few days before the fish get used to it. Try placing the mop closer to the water surface or use a darker colour yarn.


Making your own spawning mop is really one of the most enjoyable and satisfying jobs in the medaka hobby. With a few euros' worth of materials and half an hour of work you have an effective tool that greatly increases your breeding success. Whether you choose a floating mop with pool noodle or a sinking variant with a weight, the key lies in the right material: 100% acrylic wool is and remains the best choice. Have fun breeding, and enjoy every little ball you find among the threads!

Receive a 10% discount on your first order when you sign up for our newsletter.

Write a comment

Je e-mailadres wordt niet gepubliceerd. Verplichte velden zijn gemarkeerd met *

Search for products (0)

Back to Top
Product has been added to your cart